Search icon CANCEL
Subscription
0
Cart icon
Your Cart (0 item)
Close icon
You have no products in your basket yet
Save more on your purchases now! discount-offer-chevron-icon
Savings automatically calculated. No voucher code required
Arrow left icon
All Products
Best Sellers
New Releases
Books
Videos
Audiobooks
Learning Hub
Newsletters
Free Learning
Arrow right icon
Arrow up icon
GO TO TOP
Instant Citrix Security How-to

You're reading from   Instant Citrix Security How-to A guide to bulletproofing your enterprise environment with the excellent security features in Citrix

Arrow left icon
Product type Book
Published in Feb 2013
Publisher Packt
ISBN-13 9781849686723
Pages 74 pages
Edition 1st Edition
Languages
Arrow right icon
Author (1):
Arrow left icon
Carmel V Jacob Carmel V Jacob
Author Profile Icon Carmel V Jacob
Carmel V Jacob
Arrow right icon
View More author details
Toc

Disaster recovery (Should know)


Imagine load balancing a pair of NetScaler devices across geographical locations, so that traffic is always passing through, irrespective of whether it uses the main site or an alternate site (during major outages or if there is an excess load of traffic) based on the selected LB algorithms; that is GSLB for you. This section briefs about setting up the GSLB disaster recovery.

Getting ready

NetScaler can be set up in many different ways for GSLB, some of which are listed as follows:

  1. NetScaler as the Authoritative DNS (ADNS) server (by configuring a service on DNS port number 53)

  2. NetScaler as Authoritative subdomain name server (by assigning a part of the domain alone to NS)

  3. NS as the DNS proxy (by configuring the LB vserver and binding DNS servers to it)

Starting from NetScaler version 10, even with static proximity configured, there is an option to override the static mapping of location database with a specific DNS policy, and action to direct the traffic coming from a specific Local DNS (LDNS) server, or network to specific gslb services. Follow the next screenshot to statically configure the IP address and location database on GUI.

On the Configuration Utility panel, go to GSLB | Location to create static location entries:

The setup entails a main site that processes traffic all the time and a disaster recovery site that comes up when the main site goes down. The entire GSLB algorithm is DNS-based. The GSLB configuration can be used for the following:

  • Disaster recovery

  • Load sharing

  • Proximity/performance

The Citrix NetScaler Metric Exchange Protocol (MEP) is a channel of communication between NetScaler devices across various geographical locations; it works on TCP port 3011 and, to be secure, port 3009. It is a NetScaler proprietary protocol and is used in GSLB to monitor the health of the sites. There are also the typical monitors that are bound to the load LB vserver.

With MEP and monitors enabled, the health of the remote sites can be measured from the monitors. But if monitors are not enabled, then the health of the site is measured with the help of MEP. The CLI command to enable MEP is as follows:

root@ns>set gslb site Packtsite -metricExchange  ?
 ENABLED
 DISABLED

The site metrics, the network metrics, and persistence information are shared between the GSLB sites only if the MEP is enabled. An important note is to check if the feature is enabled before you get started with the GSLB configuration. If you are going with the static proximity type of GSLB, then you would need to load the location database on the NetScaler device. To verify whether the database is properly loaded, issue the show locationparameter command and check the current static entries. If the incoming traffic does not match any entry in the location database, then the request is processed using the round robin method.

How to do it...

We will focus on a few case studies, most commonly seen in GSLB.

Case 1: The three critical aspects for GSLB are the Gslb site, Gslb vserver, and Gslb service. The site address references NetScaler at each location. These three aspects are interlinked to make it easier for the traffic to be sent to the right location.

For example, there are two sites in this recipe, main and DR. You will have to repeat the configuration on both the devices:

  1. Domain: www.packttest.com

    • ADNS servers: 172.16.1.6 for the main and DR sites

    • Vservers: 172.16.32.24 for the main site and 172.16.32.114 for the DR site

    • Site addresses: 171.12.12.33 for the main site and 171.12.12.3 for the DR site

  2. Configure the gslb sites as follows:

    add gslb site gslb_local 171.12.12.33 -publicIP 171.12.12.33
    add gslb site gslb_remote 171.12.12.3-publicIP 171.12.12.3
    
  3. Configure the gslb services: The gslb service might be a LB vserver or a direct third-party server:

  4. Configure the gslb vserver and bind the services to the vserver:

    add gslb vserver packtmain_gslb_vserver HTTP
    add gslb vserver packtdr_gslb_vserver HTTP
    bind gslb vserver packtmain_gslb_vserver -serviceName test
    bind gslb vserver packtdr_gslb_vserver -serviceName test_dr
    
  5. An important configuration is setting the backup vserver under the Advanced tab:

    set gslb vserver packtmain_gslb_vserver -backupVServer packtdr_gslb_vserver
    
  6. Bind the domain to the gslb vserver as follows:

    bind gslb vserver packtmain_gslb_vserver -domainName www.packttest.com -TTL 5
    
  7. Last but not the least, the ADNS service should be configured in NetScaler in such a way that NS would become authoritative for the domain www.packttest.com. The CLI command to configure NetScaler as an ADNS service is as follows:

    >add service main_site_adns_server 172.16.1.6 ADNS 53
    

The IP address that is used here can be a MIP or SNIP address.

Case 2: The previous section shows the basic GSLB setup. In this case study, we will see the Dynamic proximity process, where NetScaler chooses the site that has the least Round trip time (RTT). For the first time alone, NetScaler chooses a site using the round robin method and then begins its RTT calculation using the following three steps in the same order sequentially:

  1. ICMP

  2. DNS

  3. TCP

In the event that ICMP is blocked mid-way before reaching the site (anywhere on the Internet), it uses the second method listed (that is, DNS query), and finally a TCP handshake is used for the RTT calculation if the DNS query also does not give a response. This procedure is depicted in the next screenshot.

The RTT table can be viewed in the Configuration Utility tab under GSLB | LDNS Entries. If RTT shows as 0, then the time taken is less than one millisecond and if RTT shows as T-out then it indicates that the destination is unreachable. If all three preceding methods fail, it will take the backup LB method configured.

We can also use the static location database that maps the IP address range to the location area. This database is then loaded on the appliance. When the client's LDNS requests the site IP address from NetScaler, which acts as the ADNS, NetScaler parses through this location database to determine the location of the client's LDNS IP address, and then sends the nearest site IP address to the client. This method is called Static Proximity:

The CLI command to configure dynamic proximity is as follows:

>set gslb vserver packtGSLB -lbMethod MethodType
>set gslb vserver packtGSLB –lbMethod RTT

The RTT is calculated between the LDNS of the client and the site IP address.

How it works...

In both the case studies, NetScaler first receives the DNS request in case it is acting as the ADNS for that particular domain, and according to the LB algorithm set, it directs the response either to itself or another NetScaler situated in a different geographical location. In this recipe, since we are only focusing on disaster recovery, the main site will continue to process traffic until it goes down.

The GSLB local and remote site is used for the Metric Exchange Protocol (MEP) communication to share the status and health of the sites. When configuring sites on NetScaler, there is an option for the public IP address. This can be left blank if there is no firewall in the picture that does any NAT translation.

To check if the configuration is accurate, run the following command:

root@ns# host www.packttest.com 172.16.1.6

The output will be similar to the following:

Using domain server: 
Name: 172.16.1.6
Address: 172.16.1.6#53 

The aliases are:

www.domain.com has address 171.12.12.33.

The following image shows the flow of GSLB at its basic level:

There's more...

This section concentrates on tidbits and troubleshooting techniques:

Tips and troubleshooting:

  1. Run the following CLI command to check the GSLB sites:

    root@NS> show gslb site 
             1)      packtsiteA (10.xx.xx.xx)        Site Type: REMOTE
                Metric exchange: ENABLED        Metric exchange status:         ACTIVE  Public IP: 10.xx.xx.xxNetwork metric exchange: ENABLED        Persistence session     exchange: ENABLEDTrigger Monitors: ALWAYS
             2)      packtsiteA (10.xx.xx.xx)  Site Type: LOCALMetric exchange: ENABLED        Public IP: 10.xx.xx.xx 
    ------OUTPUT SNIPPED------
    

    From the preceding output, we can see that NetScaler configured for GSLB will have one local and one or many remote sites (NetScalers in different data center locations).

  2. Check for the GSLB vserver as follows:

    root@NS> show gslb vservers
    1)      packtvserver - HTTP        State: UP
            Last state change was at XXXXXXXXXXXXXXX (x ms)
            Time since last state change: 0 days, xx:xx:xx.xx
            Configured Method: LEASTCONNECTION
            Current Method: Round Robin, Reason:  Bound service's state changed to UP
            No. of Bound Services :  1 (Total)       1 (Active)
            Persistence: NONE
            Disable Primary Vserver on Down: DISABLED       Site Persistence: NONE
            Backup: packt_gslb_vserver Backup Session Timeout: 0
    ----OUTPUT SNIPPED----------
    

    The preceding output shows the gslb vserver, where the domain name for the site is configured and the gslb services are bound.

  3. Check for GSLB services as follows:

    root@ns> show gslb service
    1)      packtsvc (10.xx.xx.xx: 80)- HTTP     Server:    10.xx.xxx.xx          State: UP
            Effective State: UP
            Max Conn: 0                     Max Bandwidth: 0 kbits
            PublicIP: 10.xx.xxx.xx PublicPort: 80
            Type: REMOTE                    Site Name: packtsiteA
            Client IP: DISABLED
            Down state flush: ENABLED
            Site Persistence: NONE
            Threshold: BELOW     
    

The preceding output shows the target LB or CS vserver and the LB method configured. NetScaler can be configured with a local and many remote GSLB services.

You have been reading a chapter from
Instant Citrix Security How-to
Published in: Feb 2013
Publisher: Packt
ISBN-13: 9781849686723
Register for a free Packt account to unlock a world of extra content!
A free Packt account unlocks extra newsletters, articles, discounted offers, and much more. Start advancing your knowledge today.
Unlock this book and the full library FREE for 7 days
Get unlimited access to 7000+ expert-authored eBooks and videos courses covering every tech area you can think of
Renews at $19.99/month. Cancel anytime